电子信息工程论文.doc

约42页DOC格式手机打开展开

电子信息工程论文,目 录绪 论11 系统总体方案设计31.1 方案的设定与论证31.1.1 方案一31.1.2 方案二31.2 方案的确定42 系统硬件电路设计52.1 检测电路的设计52.1.1 温度检测电路52.1.2 湿度检测电路62.1.3 烟雾检测电路72.2 信号处理电路的设计72.2.1 程控放大电路72....
编号:30-194722大小:1.30M
分类: 论文>通信/电子论文

内容介绍

此文档由会员 lanxin520 发布

电子信息工程论文

目  录

绪  论 1
1 系统总体方案设计 3
1.1 方案的设定与论证 3
1.1.1 方案一 3
1.1.2 方案二 3
1.2 方案的确定 4
2 系统硬件电路设计 5
2.1 检测电路的设计 5
2.1.1 温度检测电路 5
2.1.2 湿度检测电路 6
2.1.3 烟雾检测电路 7
2.2 信号处理电路的设计 7
2.2.1 程控放大电路 7
2.2.2 跟随器 8
2.2.3 数字滤波器 8
2.2.4 多路开关 8
2.3 存储器的扩展 9
2.3.1 控制信号及片选信号 9
2.3.2 各芯片地址空间分配 9
2.4 I/O端口的扩展 10
2.4.1 8255A与单片机的连接 11
2.4.2 8255A地址口的确定 11
2.4.3 A/D转换电路 11
2.5 硬件外设电路设计 13
2.5.1 键盘/显示器接口电路 13
2.5.2 继电器与单片机的连接电路 14
2.5.3 蜂鸣音报警电路 15
3 系统所使用芯片简介 16
3.1 AD590 温度传感器 16
3.2 HS1101湿度传感器 17
3.3 TGS202气敏传感器 17
3.4 A/D转换器ICL7109 18
3.4.1 ICL7109特性 18
4 系统软件设计 19
4.1 软件设计原理及介绍 19
4.1.1 总系统体系设计 19
4.1.2 I/O端口的扩展程序 21
4.1.3 程控放大 21
4.1.4 中值滤波 22
4.1.5 显示子程序 23
4.1.6 定时程序 24
5 系统功能简介 25
6 硬件设计结果 26
7 系统仿真及调试 28
7.1 系统功能模块仿真 28
7.1.1 温度仿真 28
7.1.2 系统火灾报警仿真 28
7.2 系统仿真结果显示 29
结  论 30
参考文献…………………………………………………………………………..…………31
附  录 32
致  谢 37


 
仓库温、湿度检测及火灾报警系统的设计

摘  要

  本文设计了一种基单片机控制技术的仓库温、湿度检测及火灾报警系统。系统分别由AD590温度传感器、HS1101湿度传感器、TGS202气敏传感器来获取和控制温度、湿度和气体浓度的信号,并利用A/D转换器将其转换为数字信号。当仓库温度和湿度高于正常温湿度时能及时的进行自动调控,并且恢复正常温湿度,若仓库里的气体含量产生异常时,启动报警装置。用户可以通过键盘设置需要的参数及报警的上下限值,并通过数码管显示。系统为单片机测试系统,含温、湿度和气敏传感器电路、量程放大电路、信号滤波电路、A/D转换电路等电子电路、继电器、单片机等硬件电子电路。本系统具有自动巡检测控、自动显示、信号自动处理和 信息自动传输等基本功能。系统主要通过软件编程设计,实现温、湿度测试及火灾报警。该系统可实时测试、控制,且稳定性好、操作简单,可广泛用于农业、林业等部门的相关控制部分。
【关键词】 单片机   温度  湿度  传感器  火灾报警

 

 

 

 

 

 

 

 


The Warehouse Temperature,Humidity Test
And Ffire Alarm System's Design

Abstract

The article design introduces a kind of warehouse temperature and humidity test and the fire alarming system based on the single chip microcomputer control technology.The system gains the signal of by the temperature, the humidity, and the gas content AD590 temperature sensor, the HS1101 humidity sensor, the TGS202 gas sensor gains and the control temperature, the humidity and the gas strength signal separately, and then uses A/D to transfer them into the digital signals.When the warehouse temperature and the humidity are higher than the normal humiture can prompt carry on the automatic regulation, and restores the normal humiture, if in the warehouse gas content produces exceptionally time, start alarm device.The users can set the necessary parameters via the keyboard and the upper and lower alarm limits, and through the digital display.This test system is microprocessor systems, including temperature, humidity and gas sensor circuit, range amplifier; signal filtering circuit, A/D conversion circuits and other electronic circuits, relays, microcontroller hardware such as electronic circuits. This system has inspects automatically the observation, the automatic demonstration, the signal automatic reduction and the information automatic transmission and so on basic function. The system mainly through the software programming design, realizes warm, the humidity test and the fire warning.This system may the real-time test, the control, and the stability is good, simplicity of operator, it widely uses in department's and so on agriculture, forestry correlation control parts.
【Keywords】Single chip microcomputer   Temperature   Humidity     Sensor     Fire alarming