带式输送机-论文.doc

带式输送机-论文

摘   要

本次是关于TD系列型皮带输送机的设计。首先对输送机作了简单的概述，带式输送机是煤矿最理想的高效连续运输设备，与其他运输设备相比，不仅具有长距离、大运量、连续输送等优点，而且运行可靠,易于实现自动化、集中化控制,特别是对高产高效矿井，带式输送机已成为煤炭高效开采机电一体化技术与装备的关键设备。接着分析了带式输送机的选型原则及计算方法，例如驱动滚筒，改向滚筒的设计及减速器电机的选型。然后根据这些设计准则与计算选型方法按照给定参数要求进行选型设计；接着对所选择的输送机各主要零部件进行了校核。TD-75型皮带输送机由六个主要部件组成：传动装置，机尾和导回装置，中部机架，拉紧装置以及胶带。最后简单的说明了输送机的安装与维护。目前，胶带输送机正朝着长距离，高速度，低摩擦的方向发展，近年来出现的气垫式胶带输送机就是其中的一个。在胶带输送机的设计、制造以及应用方面,目前我国与国外先进水平相比仍有较大差距。本次带式输送机设计代表了设计的一般过程, 对今后的选型设计工作有一定的参考价值。                      
关键词：
带式输送机；选型设计；主要部件

Abstract
The design is a graduation project about the belt conveyor used in coal mine. At first, it is introduction about the belt conveyor. Coal belt conveyor is the ideal transport equipment in succession, as compared to other transport equipment not only has the long-distance, large volume, continuous transport, etc., but also reliable, easy to implement automated, centralized control, especially Productive and Efficient Mine, efficient coal mining belt has become mechanical and electrical integration technologies and equipment, key equipment.•
 Next, it is the principles about choose component parts of belt conveyor. For example, drive roller, bend pulley design and selection of gear motors.
After that the belt conveyor abase on the principle is designed. Then, it is checking computations about main component parts. The ordinary belt conveyor consists of six main parts: Drive Unit, Jib or Delivery End, Tail Ender Return End, Intermediate Structure, Loop Take-Up and Belt. At last, it is explanation about fix and safeguard of the belt conveyor. Today, long distance, high speed, low friction is the direction of belt conveyor’s development. Air cushion belt conveyor is one of them. At present, we still fall far short of abroad advanced technology in design, manufacture and using. There are a lot of wastes in the design of belt conveyor.
Keyword: belt conveyor; Electrotype Design; main parts

目录
摘   要 1
目录 4
1绪论 6
2  带式输送机的概述 7
2.1  带式输送机的应用 7
2.2  带式输送机的分类 7
2.3  带式输送机的发展状况 9
2.4  带式输送机的工作原理及布置情况 10
3  带式输送机的设计计算 13
3.1  已知带式输送机的原始数据 13
3.2  带式输送机的计算 13
3.3  带式输送机总阻力由下式计算 16
3.4  胶带核算 22
3.5  允许垂直核算 22
3.6  车式拉紧装置重锤重量计算 22
3.7  电动机功率 23
4  减速器的选型 24
4.1  确定传动比 24
5  输送带部件的选用 25
5.1  输送带 25
5.2  传动滚筒 29
5.3托辊 33
5.3.1托辊的选型 33
5.3.2托辊的校核 40
5.4  制动装置 42
5.5  改向装置 43
5.6  拉紧装置 45
5.6.1  拉紧装置的作用 45
5.6.2  张紧装置在使用中应满足的要求 45
6  其他部件的选用 47
6.1  机架与中间架 47
6.2  卸料装置 48
6.3  清扫装置 49
6.4  头部漏斗 50
6.5  电气及安全装置 51
7 总结 52
致    谢 53
参考文献 54