滤油器支架模具设计_毕业论文.rar
滤油器支架模具设计_毕业论文,资源包括标准doc格式正文共40页 附制件图.dwg 装配图1.dwg 装配图2.dwg 装配图3.dwg 零件图1.dwg 零件图2.dwg 零件图3.dwg摘要本说明书主要是阐述了有关滤油器支架模具设计的基本过程和其主要计算。全文共由四章组成，他们的内容如下所述。第一章是设计滤油器支架模具的工艺方案的确定，主要根据...
该文档为压缩文件,包含的文件列表如下:
内容介绍
原文档由会员 莎士比亚 发布
资源包括标准DOC格式正文共40页 附制件图.dwg 装配图1.dwg 装配图2.dwg 装配图3.dwg 零件图1.dwg 零件图2.dwg 零件图3.dwg
摘要
本说明书主要是阐述了有关滤油器支架模具设计的基本过程和其主要计算。全文共由四章组成，他们的内容如下所述。
第一章是设计滤油器支架模具的工艺方案的确定，主要根据所给制件特点加以分析，设计出合理的模具，这里共设计出三套模具。第二章是落料拉深复合模的设计，其中包括一些典型结构的选择和一些非标准零件的设计。第三章是冲孔切边复合模的设计，包括各种模具零件的选择和一些零件尺寸的计算。第四章是弯曲翻边复合模的设计，此章除了沿用了相关类似模具结构外，还进行了简单的计算和零件设计。
鉴于本人的水平所限，在设计中肯定有不足之处存在，也可能有错误出现，恳请评阅老师和各位读者包涵并且批评指正。
关键词： 模具 复合模 零件
Abstract
This paper is main elaborates the basic mould design course of the sieve oil implement’s bracket,and expounds the main calculation course for it.
There are four parts in this paper, their content as follow.
The first chapter is settling the project of the mould design’s craft to the sieve oil implement’s bracket. It main contains the analysis of the sieve oil implement’s bracket’s characteristics. Make sure design three suitable moulds. The second chapter is the design of the blanking and drawing compound dies. It contains the choosing of the typical framework of the dies. The design
of some accessory. The third chapter is the design of the piercing and trimming compound dies. It contains the choosing the caculation of accessory. The forth chapter is the design of bending and flanging compound dies. In addition to using the similar framework of the dies, it contains some calculation and design of accessory.
In view of my limited knowledge,I could have made some mistakes in this paper, I wish my teacher and the readers could help me correct it, thanks!
Keywords: mould compound dies accessory
目录
第一章 工艺方案的确定………………………………………………………………4
第二章 落料拉深复合模的设计………………………………………………………7
第三章 冲孔修边复合模的设计………………………………………………………19
第四章 弯曲翻边复合模的设计………………………………………………………30
毕业设计总结……………………………………………………………………………39
参考文献…………………………………………………………………………………40
摘要
本说明书主要是阐述了有关滤油器支架模具设计的基本过程和其主要计算。全文共由四章组成，他们的内容如下所述。
第一章是设计滤油器支架模具的工艺方案的确定，主要根据所给制件特点加以分析，设计出合理的模具，这里共设计出三套模具。第二章是落料拉深复合模的设计，其中包括一些典型结构的选择和一些非标准零件的设计。第三章是冲孔切边复合模的设计，包括各种模具零件的选择和一些零件尺寸的计算。第四章是弯曲翻边复合模的设计，此章除了沿用了相关类似模具结构外，还进行了简单的计算和零件设计。
鉴于本人的水平所限，在设计中肯定有不足之处存在，也可能有错误出现，恳请评阅老师和各位读者包涵并且批评指正。
关键词： 模具 复合模 零件
Abstract
This paper is main elaborates the basic mould design course of the sieve oil implement’s bracket,and expounds the main calculation course for it.
There are four parts in this paper, their content as follow.
The first chapter is settling the project of the mould design’s craft to the sieve oil implement’s bracket. It main contains the analysis of the sieve oil implement’s bracket’s characteristics. Make sure design three suitable moulds. The second chapter is the design of the blanking and drawing compound dies. It contains the choosing of the typical framework of the dies. The design
of some accessory. The third chapter is the design of the piercing and trimming compound dies. It contains the choosing the caculation of accessory. The forth chapter is the design of bending and flanging compound dies. In addition to using the similar framework of the dies, it contains some calculation and design of accessory.
In view of my limited knowledge,I could have made some mistakes in this paper, I wish my teacher and the readers could help me correct it, thanks!
Keywords: mould compound dies accessory
目录
第一章 工艺方案的确定………………………………………………………………4
第二章 落料拉深复合模的设计………………………………………………………7
第三章 冲孔修边复合模的设计………………………………………………………19
第四章 弯曲翻边复合模的设计………………………………………………………30
毕业设计总结……………………………………………………………………………39
参考文献…………………………………………………………………………………40
