毕业设计:车床组合夹具的设计.zip

ZIP格式版权申诉手机打开展开

毕业设计:车床组合夹具的设计,论文说明书共32页,字数总计:16365资料内容简介:a0-法兰盘.dwga0-组合夹具总装配图.dwga2-连接板.dwga2-压板.dwga3-螺柱.dwga4-挡铁.dwga4-定位块.dwga4-三通阀零件图1.dwga4-三通接头.dwga_clamping_design_appr...
编号:68-287823大小:1.58M
分类: 论文>机械工业论文

该文档为压缩文件,包含的文件列表如下:

内容介绍

原文档由会员 lixiuhui7 发布

毕业设计:车床组合夹具的设计
论文说明书共32页,字数总计:16365
资料内容简介:
A0-法兰盘.dwg
A0-组合夹具总装配图.dwg
A2-连接板.dwg
A2-压板.dwg
A3-螺柱.dwg
A4-挡铁.dwg
A4-定位块.dwg
A4-三通阀零件图1.dwg
A4-三通接头.dwg
A_Clamping_Design_Approach_for_Automated_Fixture_Design.doc.pdf
毕业设计论文说明书:车床组合夹具的设计.doc
开题报告.doc
外文文献 2.doc
中期报告.doc
车床组合夹具设计
摘 要

根据六点定位原理和定位基准的选择原则,采用长V型块,支承块和定位挡铁定位。长V型块置于拱形肋板后限制x轴的两自由度和z轴的两自由度,挡铁置于孔端限制绕y轴旋转的自由度,支承块置于肋板下方限制沿y轴移动的自由度。依据相关原理计算定位误差。根据夹紧方式的选择原则,选择夹紧元件为压板压头和V型块,然后通过切削力进行夹紧力的计算。夹紧的动力装置选用手动压紧装置。按照定位元件和夹紧元件设计连接件。
以所选元件和装置为基础确定夹具总体布局和夹具体的结构形式,并确定好定位元件在夹具体上的位置。绘制夹具方案设计,进行工序精度分析。对以上设计进行审核。最后设计夹具总装配图。

关键词:组合夹具;定位;夹紧;三通接头


Lathe modular jig and fixture design
Abstract
According to six localizations principles and selection principle of the localization datum, using the long V block, the supporting block and the localization comes true the hard localization. The long V block putted in the arch ribbed plate to limit two degrees of freedom in the x axis and the z axes two degrees of freedom, the iron putted in the hole end limit to the degree of freedom which circle the y rotation of axis, the supporting block putted under the ribbed plate to limit degree of freedom along the y axis migration. Position error is reckoned by the correlation principle. According to the way of the selection principle, discharge head and V block is selected to clamp the part. Then computation of the strength is achieved by carrying on through the cutting force clamps. The power of clamps is from the hydraulic unit. Design of bridge piece is according to the location part and the clamp part. The guide part designing in this topic is not requested because the cutter bar is short. Other parts and equipment are designed following last process.
The jig overall arrangement and concrete structure of the body clamp are determined with the above part and the equipment. The position of the components in the kits specific location must be guaranteed, and then design the jig, carry on the working procedure precision analysis. The design review is following. Finally the jig assembly drawing is achieved.

Keywords: Modular jig and fixture; location; clamp; union tee

目 录
1绪论…………………………………………………………………………………1
1.1概述…………………………………………………………………………………1
1.1.1车床夹具的分类………………………………………………………………1
1.1.2夹具的组成……………………………………………………………………2
1.1.3夹具体…………………………………………………………………………3
1.1.4车床夹具在机械加工中的作用………………………………………………3
1.1.5车床夹具在车床中的地位及作用……………………………………………3
1.1.6国内外夹具的发展与趋势……………………………………………………4
1.2夹具研究现状………………………………………………………………………5
1.2.1机床夹具的现状………………………………………………………………5
1.2.2现代机床夹具的发展方向……………………………………………………6
1.3国内外对组合夹具的发展及研究状况……………………………………………7
1.3.1国内对组合夹具的发展状况…………………………………………………7
1.3.2国外对组合夹具的发展状况…………………………………………………8
1.4本文主要研究内容…………………………………………………………………9
2零件分析…………………………………………………………………………10
2.1零件的选择与分析………………………………………………………………10
2.2工艺路线的确定…………………………………………………………………10
2.3总体设计中对夹具设计的重要的参数………………………………………… 11
3车床组合的夹具设计………………………………………………………… 12
3.1夹具设计要求与选型……………………………………………………………12
3.1.1夹具设计要求…………………………………………………………………12
3.1.2夹具的选型……………………………………………………………………13
3.2定位和夹紧方案的确定…………………………………………………………13
3.2.1定位和夹紧方案的选择分析…………………………………………………14
3.3定位元件和夹紧元件的设计计算………………………………………………15
3.3.1定位元件的设计计算………………………………………………………… 15
3.3.2夹紧机构的设计计算…………………………………………………………16
3.4误差分析计算……………………………………………………………………17
3.4.1影响加工精度的因素…………………………………………………………17
3.4.2误差的计算……………………………………………………………………17

3.4.3保证加工精度………………..