三爪卡盘增力机构夹具设计.doc
约26页DOC格式手机打开展开
三爪卡盘增力机构夹具设计,[摘要]设计是在三爪卡盘上加装摆动式液压缸和平面螺旋机构的螺旋摆动式液压缸增力机构的结构。传统的机床如车床、铣床上三爪卡盘的工作一般依靠工人用手工进行夹紧,这不但增加了工人的劳动强度,而且所需夹紧力非常大,还常常有夹不紧的情况,阻碍了生产率的提高。通过在三爪卡盘加装摆动式液压缸和平面螺旋机构构成...
内容介绍
此文档由会员 小花仙66 发布
三爪卡盘增力机构夹具设计
[摘要] 设计是在三爪卡盘上加装摆动式液压缸和平面螺旋机构的螺旋摆动式液压缸增力机构的结构。传统的机床如车床、铣床上三爪卡盘的工作一般依靠工人用手工进行夹紧,这不但增加了工人的劳动强度,而且所需夹紧力非常大,还常常有夹不紧的情况,阻碍了生产率的提高。通过在三爪卡盘加装摆动式液压缸和平面螺旋机构构成螺旋摆动式液压缸增力机构,可实现与原有卡盘体的较好结合,并使外加压力能转换成圆周运动,且其结构简单,工作可靠,能达到较高的增力比,最后能达到较好的效果。
[关键词]三爪卡盘 液压缸 夹具 增力
目 录
前言·············································································································1
第一章 夹具的简介···························································································2
1.1 夹具的特点························································································2
1.2 研究夹具的目的和意义··········································································2
1.3 夹具的基本结构和原理··········································································3
第二章 三爪卡盘螺旋摆动式液压缸增力机构的结构和原理···········································3
第三章 主要参数确定与结构计算··········································································4
3.1 液压腔的结构设计················································································4
3.2 转子叶片数的设计················································································4
3.3 摆动角的设计······················································································5
3.4 定子圆柱活塞杠面积的设计·····································································5
第四章 凹槽轮廓线的设计···················································································6
4.1 轮廓面段数的确定················································································6
4.2 活塞杠升程的确定················································································6
4.3 参数θ1的设计·····················································································8
4.4 参数β的设计······················································································9
第五章 夹具在安装和操作时应注意的事项································································10
5.1 夹具的安装·························································································10
5.2 夹具在操作时应注意的事项······································································10
第六章 夹具的经济效益分析··················································································11
第七章 单工位夹具与成组夹具的分析······································································13
7.1定位基准与定位元件的选择·······································································13
7.2夹紧元件与夹紧力的选择·········································································13
7.3夹具基体的设计夹具基体··········································································13
7.4机壳成组..
[摘要] 设计是在三爪卡盘上加装摆动式液压缸和平面螺旋机构的螺旋摆动式液压缸增力机构的结构。传统的机床如车床、铣床上三爪卡盘的工作一般依靠工人用手工进行夹紧,这不但增加了工人的劳动强度,而且所需夹紧力非常大,还常常有夹不紧的情况,阻碍了生产率的提高。通过在三爪卡盘加装摆动式液压缸和平面螺旋机构构成螺旋摆动式液压缸增力机构,可实现与原有卡盘体的较好结合,并使外加压力能转换成圆周运动,且其结构简单,工作可靠,能达到较高的增力比,最后能达到较好的效果。
[关键词]三爪卡盘 液压缸 夹具 增力
目 录
前言·············································································································1
第一章 夹具的简介···························································································2
1.1 夹具的特点························································································2
1.2 研究夹具的目的和意义··········································································2
1.3 夹具的基本结构和原理··········································································3
第二章 三爪卡盘螺旋摆动式液压缸增力机构的结构和原理···········································3
第三章 主要参数确定与结构计算··········································································4
3.1 液压腔的结构设计················································································4
3.2 转子叶片数的设计················································································4
3.3 摆动角的设计······················································································5
3.4 定子圆柱活塞杠面积的设计·····································································5
第四章 凹槽轮廓线的设计···················································································6
4.1 轮廓面段数的确定················································································6
4.2 活塞杠升程的确定················································································6
4.3 参数θ1的设计·····················································································8
4.4 参数β的设计······················································································9
第五章 夹具在安装和操作时应注意的事项································································10
5.1 夹具的安装·························································································10
5.2 夹具在操作时应注意的事项······································································10
第六章 夹具的经济效益分析··················································································11
第七章 单工位夹具与成组夹具的分析······································································13
7.1定位基准与定位元件的选择·······································································13
7.2夹紧元件与夹紧力的选择·········································································13
7.3夹具基体的设计夹具基体··········································································13
7.4机壳成组..